We set up and tear down a lot of home theater and audio/video gear on a daily basis — everything from speakers and subwoofers to amplifiers, receivers, turntables, and everything in-between. And one thing that gets old really fast is cutting, stripping, and winding raw speaker wire. It's messy, it makes connecting and disconnecting components a chore, and it can leave exposed wire hanging off the back of your speaker or receiver terminals that can result in unwanted noise or poor performance.
One of the best things you can do to improve your speaker wire situation is to install that can be plugged right into compatible speaker or receiver/amplifier terminals, similar to RCA plugs. It's cheap to do, and they look clean, provide a secure connection, and make connecting and disconnecting your components really easy.
Here's how to install banana plugs on raw speaker wire.
Wire strippers, cutters, or an exacto knife
There are a few different types of banana plugs you can find at your local Best Buy, audio shop, or on Amazon, but they're pretty much the same as far as installing them goes. For our purposes, we're going to go with the that you don't have to solder and that have a small screw that you tighten.
You can find banana plugs with various fastener types and every style from to and more. It's up to you what works best.
After you've cut your speaker wire to the length you need, here's how to prep the ends for the banana plugs.
Step 1: Depending on the speaker wire you're using, there may be an outer jacket that conceals two separate wires inside, one red and one black. If this is the case, using your wire strippers, carefully strip back around 2 inches of that outer jacket to expose and separate the two wires.
Different types of speaker wire, like the wire we're using, comes joined together. Use an exacto knife to separate the two wires. They may or may not be color-coded.
Step 2: With your wires separated, use the wire strippers to strip roughly a half-inch of each wire's insulation from the ends to expose the raw wire. Be careful not to cut or damage any of the wire's strands.
With the wires exposed, you can now connect them to the banana plugs.
Step 1: First, you may have to prepare the banana plugs to accept the raw wire. In our example, you have to unscrew and separate the outer shell of the plug's housing from the internal stem. Also make sure to loosen the screws that will hold the wire in place.
Step 2: Next, insert the raw end of wire into the banana plug's core and tighten the screws to secure. Do this for both the black and red plugs and then do the same for the other end of the wire, if installing on both ends.
Step 3: Put the outer casing of the plug back on and screw it tight. That's it, you're done.
This is the easy part. Most speakers and receivers/amplifiers will have speaker terminals that have a hole in the middle for inserting banana plugs. Some have little plastic covers over the holes that you just have to remove first. Make sure to save them in a ziploc bag or a container for safe keeping.
Similar to plugging in an RCA cable, all you have to do is plug and play!
Note: Keep in mind, though, that banana plugs will not work with those spring clips found on many speakers and receivers/amplifiers.
With banana plugs installed on all your speaker wires, connecting and disconnecting your components will not only be much easier -- especially for those of you with components tucked away in a media unit that you have to pull in and out or crawl under to access -- but the electrical connection will be much stronger and more stable than messy raw wire. Plus, it couldn't be easier to do.
Apple has just launched its latest iPad mini with a notable set of upgrades, including an OLED screen, improved speakers, and a more resilient build. It also gets a new chip, and the whole package costs $200 more than its predecessor. But if you look closely at Apple’s online store, you’ll realize that $699 isn’t enough to get you the most powerful version of the A20 Pro chip inside this tablet. In fact, even if you pay $800 for the 256GB model, you still won’t get the beefiest variant. Only when you jump to the 512GB trim, which costs an absurd $999, do you get the most powerful flavor of the A20 Pro.
The $999 model gets more than extra storage
Ahead of its October 28 “Pro and Tell” event, Apple has refreshed the iPad mini with an OLED display (the first for the mini line), the company’s latest in-house, Pro-grade chipset, and something else that made me read twice: an Acoustic Display design.
The iPad mini (8th generation) starts at $699 for Wi-Fi and $849 for cellular variants. Pre-orders start October 28, 2026, and general sales begin November 6, 2026.
Apple has sent out invites for an event on October 28 in Los Angeles, and if the rumor mill is right, it's going to be a big one for Mac fans.
The MacBook Pro could get its biggest overhaul in years